Showing posts with label Off Grid Tiny House. Show all posts
Showing posts with label Off Grid Tiny House. Show all posts

Friday, July 10, 2015

Installing the Kimberly, Part 3: Modifying The Cathedral Ceiling Box

Ahh... I've fallen behind in blogging again... So, I'm going to revert to an old standard of mine: post the photos I've got now, and write the story of what's going on in them later. Check back for updates on this post some time around the beginning of August. 




Saturday, June 20, 2015

Installing the Kimberly, Part 2: Cutting The Cathedral Ceiling Box

Okay, so it took us a little longer than expected, but we got our chimney hole cut. 

Sam courageously makes the first roof puncture

It actually turned out to be a little more complicated than we had initially thought. If you want a vertical square chimney box to go through a roof panel that's on a 45-degree pitch, you can't simply hold the box flush to the panel, trace around it and cut. You have to figure out what the area of the square chimney box is on the plane of the roof panel (a rectangle), and cut that shape out of the ceiling. You also can't cut the hole perpendicular with the roof panel, but have to cut it on a 45-degree bevel from the roof (since the roof is 45-degrees off of vertical, you need to correct for that so that the cut you make is vertical), 

Fortunately our jig-saw has a bevel option, so that we can position the blade at a 45-degree angle relative to the foot. We can then hold the foot flush with the roof panel and have the blade make a vertical cut. Unfortunately, we don't have a jig-saw blade long enough to go through both  skins of our SIP. So, we cut the first one out and cleared out the polystyrene just like we did for the wheel wells. My mom was there for that part, and took a video for us. I know we've had videos of me melting the foam core of our SIPs before, but here's another one, just in case you enjoy watching the process as much as I like doing it. 



Then we were able to drill holes in the roof at the base of the hole, and from the outside measure the appropriate rectangle on the outside skin of the roof panel. Once that was cut, it was just a matter of clearing out enough foam for us to install a wooden frame inside the hole the same way the SIP manufacturers installed wooden frames inside the holes they cut for the windows. 

We called it a day after that, and tomorrow we'll frame the thing. 

Wednesday, May 20, 2015

Raising the SIPs, Part 2: Preparing the SIPs for the Wheel Wells

So, when I last left you we had gotten the first three SIP panels up on our trailer, and the next step was to prepare the next sections of wall to go over our curved sill plate above the wheel well of the trailer.


We started by cutting out a stensil we had preppared for ealier (before we put the flexible sill plate over the wheel well) by holding a scrap of OSB flush against the subfloor sheating and tracing the wheel wells onto it. We had two stensils, one for the right wheel well and one for the left. We were careful to lable which was which, as well as lableing front and back on each one. Sam used our jig saw to cut along the tracing, which then gave us a peice of wood with a curve that perfectly mirrored the curve of the wheel well. We could use this to mark where we would have to cut our SIP panel skin so that the panel will slide over the wheel well nicely. 


Now, it actually turns out that there were two panels on each side (so a total of four) which we would need to cut curves from: a 12-inch long panel and an 8-foot long panel. (The long walls of the SIP panels were designed this way so that no individual peice would be wider than 8'6" when flat packed onto our trailers since loads wider than 8'6" need an oversized load permit to drive on the roads). We started working on a 12-inch panel first. We measured out how far from the start of the panel the wheel well started, marked that distance on the bottom of our panel, and then lined up our stensil with the bottom of the panel at that mark. We scribed a line along the edge of the stensil onto the skin of the OSB and cut along that mark with the jig saw. We then did a rough foam removal, below Sam is using a chisel to clear away some of the foam.


We only cut through one side of the SIP because the inside skin will slide along the inside of the wheel well sill plate and rest on the subfloor sheathing. From the inside, you won't even be able to see where the wheel well is. 

The next step was to fur out 1.5" of foam in from the cut end of the outside SIP skin. (This opens up the space that the wheel well sill plate will occupy). Professionals use a Foam Cutting Tool for this job, which is a peice of electrically heated wire (like you see on an electric stovetop) in the shape of a rectangle, the width of a 2x4, with an adjustable depth stop. This device will melt away the foam insulation from a SIP perfectly to the depth you set it to. But we're not professionals, and we didn't really want to by a tool that would really only be useful working with SIPs. So, instead we improvised with a hand weeder and a blow torch. 


It worked great! We didn't get the same kind of precision that you could expect with the proper tool, but we're planning on drilling into the OSB all around the wheel wells and injecting spray foam in there to fill the gaps up anyway, so this doesn't bother us too much. 

Having found a system that worked, we repeated the process on the larger panels. 



Now we've just got to reassemble our lifting force and get these panels up! We plan on raising them exactly as we did the last two.

***EDIT***
One very important mistake that we made and didn't realize until we were trying to set this panel can be seen in this photo clearly: You can see that we furred out the foam an inch and a half in from the cut skin, but we left the 2x4 at the same length as the skin instead of cutting it down the 1.5" to match the foam. BIG MISTAKE! We tried to set the panel like this, and were wondering why we couldn't get it to rest on the sill plate properly... well, once we realized that it was because there was this inch and a half to 2x4 in the way we felt pretty dumb. Cutting it down was a mess (we had already put construction adhesive over every thing) and bent one of our jigsaw blades. Fortuantely, our lifting crew was SUPER AWESOME, and put up with all of our ridiculous mistakes even though it was a cold and rainy day our and they all wanted to go inside and get some lunch (as did we). The good news is that eventually we got the 2x4 cut to the right place and got the panel on properly.

Monday, March 2, 2015

Toilet and woodstove are on their way

I ordered our Toilet and Woodstove today from Vanessa at Tiny House,{Big Life}.

The Nature's Head Composting Toilet will let us life in the Tiny house without a septic system or blackwater tank (excellent videos on what living with a composting toilet is like are available from the excellent RVers blog, Gone with the Wynns)

The Kimberly Woodstove is one of the most efficient small space woodstoves on the market. Truthfully, this woodstove is incredibly expensive, costing as much as our trailer, but I think that it's a good investment. We'll be living off-grid through cold New England winters in a 120 square foot house that's got 13 windows and two skylights. If we were to get a smaller BTU propane unit and the temperature dropped or we ran out of propane, we couldn't just plug in an electric space heater to keep our pipes from freezing. I'd much rather spend more on a reliable woodstove than have to worry about how well we'll be able to heat the house during the winter.

The woodstove costs about $4,000 and the toilet just under $1,000, bringing the total cost of this particular purchase to about $5,000. I'll have to spend another $500 or so (guestimate) on the chimney for the woodstove in a week or so.

That's our Tiny House update for the week.

Monday, February 16, 2015

The Importance of Google SketchUp


I would advise any one looking into building a Tiny House (especially if you're considering SIP construction) to have a solid working knowledge of Google SketchUp first. If this incredibly powerful tool isn't in your arsenal, then you should learn it, or find someone who can help you get a 3D model of your tiny house before you build.

For us, because time is a factor and I didn't have time/energy to become fluent in a new software and still be able to get the rest of the Tiny House research done (and all the medical/legal clearance paperwork from the Peace Corps that Sam and I have been inundated with of late), we chose the latter of these options. We were really fortunate to find Joe Coover, who is working on a website to facilitate the sale of Tiny House SIP Kits. One of the biggest barriers we faced getting a SIP Tiny House was that I had no idea how to create a 3D rendering of the Tiny House and how to get that information into a format that would work for the SIP manufacturer. Joe knows the SIP guys, has ordered Tiny Houses from them in the past (including his own), and is a wiz with SketchUp. After exchanging emails with me about the details of our Tiny House, he created the beautiful SketchUp rendition of our tiny house you see above. Without this help, Sam and I never would have been able to order SIPs.

If you're dead set on doing every last piece of the puzzle yourself but don't know how to use SketchUp, Google offers some good video tutorials, and there are many other tutorials available on the web, both free and paid. Another good resource to look for is local Meetups at which SketchUp will be taught- I know that the Greater Boston Tiny House Enthusiasts Meetup Group has had several such sessions in the past, which I believe were well attended.

Whatever way you decide to go, make sure to take advantage of the incredible planning tool that is Google SketchUp. You'll have a better Tiny House for it in the end.

Monday, January 5, 2015

Tiny House Systems

In addition to learning the nuts and bolts (no, really, literal nuts and bolts) of putting a Tiny House together, I'm also having to make a lot of decisions about what systems we will have in our Tiny House. It's a little intimidating to make these choices because each one will have a big impact on our Tiny House lifestyle. The three biggest systems I've had to figure out so far are electric, heating and plumbing. Each one of these is complex enough to merit multiple posts of it's own (I'll write those later) but for right now I want to go over, in big brush strokes, what I'm thinking of for our Tiny House.

The first big choice we had to make was whether our Tiny House was going to be on-grid or off-grid as this would end up affecting lots of other decisions. Fortunately, our answer was relatively straight forward (even if it will cause challenges down the road): the North Stonington property has no improvements (no electricity, no well, no septic), and we don't know when we'll have the funds available to have them (and a proper driveway) installed. Thus, our Tiny House will have to be able to function without these things. Once we knew that, the rest fell into place.

For electricity, we will be living off solar panels and a battery bank. In order to minimize the cost (and space used by) these elements,we'll be choosing appliances which minimize electrical consumption- this rules out using electricity to produce heat.

To heat our home, we've decided to get a wood stove. A lot of people feel that this is a very dangerous decision, but I just can't get behind that thinking. Maybe I'm just desensitized to it because I grew up in a home that was heated exclusively by a wood stove, but I feel really comfortable with this choice. An added benefit to heating with a wood stove is that the model we're looking at also has an accessory thermoelectric generator that we'll be able to use in the winter to augment our solar panels.

For our other heating needs, we'll be using propane. Many natural gas ovens easily convert to LP use, and we'll be getting one of those. We'll also be using an on demand tankless water heater which runs on propane. I think that we'll probably be able to get by using a propane cylinder small enough to fit into the back seat of the car so that we can take it to the fill station ourselves rather than have to have a gas truck come up the (as of yet not-extant) driveway and fill it for us.

How will we get water to heat in our tankless propane powered water heater without a well you ask? We'll be using a rainwater catchment system for our shower and dishes with an on board 60 gallon water tank, and a series of 50 gallon drums outside the Tine House. We'll purchase drinking water and keep it in the fridge to avoid having to super-duper filter our rain water and to avoid having to drink room temp/warm water all the time. As far as dealing with our dirty water: we're going to implement a french drain system to deal with our grey water and we'll be using a composting toilet to avoid black water all together.

I hope to write more detailed posts about each of these choices later on in the process, but, for now, that's the rough outline of the systems we'll be using in our Tiny House.